Oct 5,1999 onl8v1: Solaris 7 cc ドライバのテスト. Solaris7 システムのインストール --- システム・インストール#01 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ (http://www-online.kek.jp/~inoue/Machine/onl8v1/ Solaris7/system-install1.txt) 高エネルギー加速器研究機構 素粒子原子核研究所 物理、オンライングループ 井上 栄二 (1). 現状確認 (A). SPARC CPU-8VT、Solaris7、VMEドライバが届いた。 (2). ここでやるべきこと CPU-8VT に Solaris7 のシステムをインストールする。 (3). CPU-8VTボードの設置 VMEクレートに CPU-8VTボードを設置する。 (3-1). CPUボードの配置 onl8v1 は VMEクレートのスロット番号１に挿入した。 onl8v1 の SCSI には ローカル・ディスクを ID #3 で接続し、には CD-ROMドライブを ID #6 で 接続した。 onl7v1、onl7v2、onl5v4 の cpuボードは全て抜いてある。 (3-2). onl8v1 の挿入してある VMEクレートの電源を入れる ok pp Power-On Self Test IU Register File Test MMU Context Table Reg Test MMU Context Register Test MMU Sync Fault Stat Reg Test MMU Sync Fault Addr Reg Test D-Cache Tag Ram Test D-Cache Data Ram Test D-TLB CAM Test D-TLB RAM Test I-Cache Tag Ram Test I-Cache Data Ram Test E-Cache Addr Bus Test E-Cache Tag Bus Test E-Cache Data Ram Test E-Cache Tag Ram Test Snoop Ram Test IOMMU-TLB Test IOMMU Control Register Test IOMMU Base Addr Register Test IOMMU SBus Config Registers Test Set RAH to 3 Set WS to 3 DRAM Data Bus Test Probing Bank 0 -- 32 Megs Found Probing Bank 1 -- 32 Megs Found Probing Bank 2 -- 0 Megs Found Probing Bank 3 -- 0 Megs Found Probing Bank 4 -- 0 Megs Found Probing Bank 5 -- 0 Megs Found Probing Bank 6 -- 0 Megs Found Probing Bank 7 -- 0 Megs Found DRAM Address Bus Test Memory Address Pattern Test D-Cache Hit Miss Test D-TLB Hit Miss Test I-TLB Hit Miss Test I-Cache Hit Miss Test E-Cache Hit Miss Test, cache_size=0x00080000 bytes I-TLB Ram Test FPU Register File Test FPU Misaligned Reg Pair Test FPU Single-precision Tests FPU Double-precision Tests FPU SP Invalid CEXC Test FPU SP Overflow CEXC Test FPU SP Divide-by-0 CEXC Test FPU SP Inexact CEXC Test FPU SP Trap Priority > Test FPU SP Trap Priority < Test FPU DP Invalid CEXC Test FPU DP Overflow CEXC Test FPU DP Divide-by-0 CEXC Test FPU DP Inexact CEXC Test FPU DP Trap Priority > Test FPU DP Trap Priority < Test PROC0 Interrupt Regs Tests Soft Interrupts OFF Test Soft Interrupts ON Test PROC0 User Timer Test PROC0 Counter/Timer Test DMA2 E_CSR Register Test LANCE Address Port Tests LANCE Data Port Tests DMA2 D_CSR Register Test DMA2 D_ADDR Register Test DMA2 D_BCNT Register Test DMA2 D_NADDR Register Test ESP Registers Tests DMA2 P_CSR Register Test DMA2 P_ADDR Register Test DMA2 P_BCNT Register Test PPORT Registers Tests NVRAM Access Test TOD Registers Test screen not found. Can't open input device. Keyboard not present. Using tty for input and output. SPARC CPU-8VT, No Keyboard ROM Rev. 2.15.1, 64 MB memory installed, Serial #9172389. Ethernet address 0:80:42:b:85:a5, Host ID: 808bf5a5. Boot device: /iommu/sbus/espdma@5,8400000/esp@5,8800000/sd@3,0 File and args: The file just loaded does not appear to be executable. Type help for more information ok (4). Solaris2.6 をインストールする。 (4-1). CD-ROMドライブに Solaris2.6 のメディアをセットして、パワー ON ok boot cdrom Boot device: /iommu/sbus/espdma@5,8400000/esp@5,8800000/sd@6,0:d File and args: SunOS Release 5.7 Version Generic_106541-06 [UNIX(R) System V Release 4.0] Copyright (c) 1983-1999, Sun Microsystems, Inc. Configuring devices... The system is coming up. Please wait. Select a Language 0) English 1) German 2) Spanish 3) French 4) Italian 5) Swedish ?0 Select a Locale The locale you select on this screen becomes the default displayed on your desktop after you reboot the system. Selecting a locale determines how online information is displayed for a specific locale or region (for example, time, date, spelling, and monetary value.) NOTE: The ASCII only option gives you the default 128-character set that was available in previous releases. If you do not need to send/receive international correspondence where you need locale-specific alphabetic characters (like accented or umlaut characters) the ASCII only set is sufficient. Otherwise, you can select an ISO locale which contains a 256-character set. Selecting an ISO locale can cause a minor performance degradation (in many cases, less than 5%). 0) USA (ASCII) 22) Latvia (ISO8859-13) 1) Bulgaria (ISO8859-5) 23) Macedonia (ISO8859-5) 2) Czech Republic (ISO8859-2) 24) Netherlands (ISO8859-1) 3) Denmark (ISO8859-1) 25) Belgium (ISO8859-1) 4) Denmark (ISO8859-15 - Euro) 26) Belgium (ISO8859-15 - Euro) 5) Greece (ISO8859-7) 27) Netherlands (ISO8859-15 - Euro) 6) Greece (ISO8859-7 + Euro glyph) 28) Norway (ISO8859-1) 7) Australia (ISO8859-1) 29) Norway (ISO8859-1 - Nynorsk) 8) Canada (ISO8859-1) 30) Bosnia (ISO8859-2) 9) Great Britain (ISO8859-1) 31) Poland (ISO8859-2) 10) Great Britain (ISO8859-15 - Euro) 32) Portugal (ISO8859-1) 11) Ireland (ISO8859-1) 33) Brazil (ISO8859-1) 12) Ireland (ISO8859-15 - Euro) 34) Portugal (ISO8859-15 - Euro) 13) New Zealand (ISO8859-1) 35) Romania (ISO8859-2) 14) USA (ISO8859-1) 36) Russia (ISO8859-5) 15) Estonia (ISO8859-1) 37) Russia (KOI8-R) 16) Estonia (ISO8859-15) 38) Slovakia (ISO8859-2) 17) Finland (ISO8859-1) 39) Slovenia (ISO8859-2) 18) Finland (ISO8859-15 - Euro) 40) Albania (ISO8859-2) 19) Croatia (ISO8859-2) 41) Serbia (ISO8859-5) 20) Hungary (ISO8859-2) 42) Turkey (ISO8859-9) 21) Lithuania (ISO8859-13) 43) Go Back to Previous Screen Type a number and press Return or Enter [0]: What type of terminal are you using? 1) ANSI Standard CRT 2) DEC VT52 3) DEC VT100 4) Heathkit 19 5) Lear Siegler ADM31 6) PC Console 7) Sun Command Tool 8) Sun Workstation 9) Televideo 910 10) Televideo 925 11) Wyse Model 50 12) X Terminal Emulator (xterms) 13) Other Type the number of your choice and press Return: 12 The Solaris Installation Program The Solaris installation program is divided into a series of short sections where you'll be prompted to provide information for the installation. At the end of each section, you'll be able to change the selections you've made before continuing. About navigation... - The mouse cannot be used - If your keyboard does not have function keys, or they do not respond, press ESC; the legend at the bottom of the screen will change to show the ESC keys to use for navigation. F2_Continue F6_Help Identify This System On the next screens, you must identify this system as networked or non-networked, and set the default time zone and date/time. If this system is networked, the software will try to find the information it needs to identify your system; you will be prompted to supply any information it cannot find. > To begin identifying this system, press F2. F2_Continue F6_Help Host Name On this screen you must enter your host name, which identifies this system on the network. The name must be unique within your domain; creating a duplicate host name will cause problems on the network after you install Solaris. A host name must be at least two characters; it can contain letters, digits, and minus signs (-). Host name: onl8v1 F2_Continue F6_Help Network Connectivity Specify Yes if the system is connected to the network by one of the Solaris or vendor network/communication Ethernet cards that are supported on the Solaris CD. See your hardware documentation for the current list of supported cards. Specify No if the system is connected to a network/communication card that is not supported on the Solaris CD, and follow the instructions listed under Help. Networked [X] Yes [ ] No F2_Continue F6_Help Primary Network Interface On this screen you must specify which of the following network adapters is the system's primary network interface. Usually the correct choice is the lowest number. However, do not guess; ask your system administrator if you're not sure. > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X]. Primary network interface [X] le0 [ ] le1 F2_Continue F6_Help IP Address On this screen you must enter the Internet Protocol (IP) address for this system. It must be unique and follow your site's address conventions, or a system/network failure could result. IP addresses contain four sets of numbers separated by periods (for example 129.200.9.1). IP address: 130.87.219.78 F2_Continue F6_Help Confirm Information > Confirm the following information. If it is correct, press F2; to change any information, press F4. Host name: onl8v1 Networked: Yes Primary network interface: le0 IP address: 130.87.219.78 F2_Continue F4_Change F6_Help Name Service On this screen you must provide name service information. Select the name service that will be used by this system, or None if your system will either not use a name service at all, or if it will use a name service not listed here. > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X]. Name service [ ] NIS+ [ ] NIS [X] DNS [ ] None F2_Continue F6_Help Domain Name On this screen you must specify the domain where this system resides. Make sure you enter the name correctly including capitalization and punctuation. Domain name: kek.jp F2_Continue F6_Help DNS Server Addresses On this screen you must enter the IP address of your DNS server(s). You must enter at least one address. IP addresses must contain four sets of numbers separated by periods (for example 129.200.9.1). Server's IP address: 130.87.216.2 Server's IP address: 130.87.34.2 Server's IP address: F2_Continue F6_Help DNS Search List On this screen you can enter a list of domains that will be searched when a DNS query is made. If you do not enter any domains, DNS will only search the DNS domain chosen for this system. The domains entered, when concatenated, may not be longer than 250 characters. Search domain: Search domain: Search domain: Search domain: Search domain: Search domain: F2_Continue F6_Help Confirm Information > Confirm the following information. If it is correct, press F2; to change any information, press F4. Name service: DNS Domain name: kek.jp Server address(es): 130.87.216.2 130.87.34.2 F2_Continue F4_Change F6_Help Subnets On this screen you must specify whether this system is part of a subnet. If you specify incorrectly, the system will have problems communicating on the network after you reboot. > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X]. System part of a subnet [X] Yes [ ] No F2_Continue F6_Help Netmask On this screen you must specify the netmask of your subnet. A default netmask is shown; do not accept the default unless you are sure it is correct for your subnet. A netmask must contain four sets of numbers separated by periods (for example 255.255.255.0). Netmask: 255.255.248.0 F2_Continue F6_Help Time Zone On this screen you must specify your default time zone. You can specify a time zone in three ways: select one of the geographic regions from the list, select other - offset from GMT, or other - specify time zone file. > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X]. Regions ^ [ ] Asia, Western [ ] Australia / New Zealand [ ] Canada [ ] Europe [ ] Mexico [ ] South America [ ] United States [ ] other - offset from GMT - [X] other - specify time zone file F2_Continue F6_Help Time Zone File Specify the time zone file you want to use. The file must already be in the /usr/share/lib/zoneinfo directory. You do not need to enter the full path. File name: Japan F2_Continue F5_Cancel F6_Help Date and Time > Accept the default date and time or enter new values. Date and time: 1999-10-05 14:45 Year (4 digits) : 1999 Month (1-12) : 10 Day (1-31) : 05 Hour (0-23) : 14 Minute (0-59) : 45 F2_Continue F6_Help Confirm Information > Confirm the following information. If it is correct, press F2; to change any information, press F4. System part of a subnet: Yes Netmask: 255.255.248.0 Time zone: Japan Date and time: 1999-10-05 14:45:00 F2_Continue F4_Change F6_Help System identification is completed. Starting Solaris installation program... Executing JumpStart preinstall phase... Searching for SolStart directory... Checking rules.ok file... Using begin script: install_begin Using finish script: patch_finish Executing SolStart preinstall phase... Executing begin script "install_begin"... Begin script install_begin execution completed. Solaris Interactive Installation This system is upgradable, so there are two ways to install the Solaris software. The Upgrade option updates the Solaris software to the new release, saving as many modifications to the previous version of Solaris software as possible. Back up the system before using the Upgrade option. The Initial option overwrites the system disks with the new version of Solaris software. This option allows you to preserve any existing file systems. Back up any modifications made to the previous version of Solaris software before starting the Initial option. After you select an option and complete the tasks that follow, a summary of your actions will be displayed. F2_Upgrade F4_Initial F5_Exit F6_Help Solaris Interactive Installation You'll be using the initial option for installing Solaris software on the system. The initial option overwrites the system disks when the new Solaris software is installed. On the following screens, you can accept the defaults or you can customize how Solaris software will be installed by: - Allocating space for diskless clients or AutoClient systems - Selecting the type of Solaris software to install - Selecting disks to hold software you've selected - Specifying how file systems are laid out on the disks After completing these tasks, a summary of your selections (called a profile) will be displayed. F2_Continue F3_Go Back F5_Exit F6_Help Allocate Client Services? Do you want to allocate space for diskless clients and/or AutoClient systems? F2_Continue F3_Go Back F4_Allocate F5_Exit F6_Help Select Languages Select the languages you want for displaying the user interface after Solaris software is installed. English is automatically installed by default. [ ] French [ ] German [ ] Italian [ ] Spanish [ ] Swedish F2_Continue F3_Go Back F5_Exit F6_Help Select 64 Bit Select 64-bit if you want to install the Solaris 64-bit packages on this system. [ ] Select To Include Solaris 64-bit Support F2_Continue F3_Go Back F5_Exit Select Software Select the Solaris software to install on the system. NOTE: After selecting a software group, you can add or remove software by customizing it. However, this requires understanding of software dependencies and how Solaris software is packaged. [X] Entire Distribution plus OEM support ....... 962.00 MB (F4 to Customi ze) [ ] Entire Distribution ........................ 913.00 MB [ ] Developer System Support ................... 854.00 MB [ ] End User System Support .................... 398.00 MB [ ] Core System Support ........................ 136.00 MB F2_Continue F3_Go Back F4_Customize F5_Exit F6_Help Select Disks On this screen you must select the disks for installing Solaris software. Start by looking at the Suggested Minimum field; this value is the approximate space needed to install the software you've selected. Keep selecting disks until the Total Selected value exceeds the Suggested Minimum value. Disk Device (Size) Available Space ============================================= [ ] c0t2d0 (8652 MB) 8652 MB [X] c0t3d0 (8652 MB) boot disk 8652 MB Total Selected: 8652 MB Suggested Minimum: 641 MB F2_Continue F3_Go Back F4_Edit F5_Exit F6_Help Preserve Data? Do you want to preserve existing data? At least one of the disks you've selected for installing Solaris software has file systems or unnamed slices that you may want to save. F2_Continue F3_Go Back F4_Preserve F5_Exit F6_Help Automatically Layout File Systems? Do you want to use auto-layout to automatically layout file systems? Manually laying out file systems requires advanced system administration skills. F2_Auto Layout F3_Go Back F4_Manual Layout F5_Exit F6_Help Automatically Layout File Systems On this screen you must select all the file systems you want auto-layout to create, or accept the default file systems shown. NOTE: For small disks, it may be necessary for auto-layout to break up some of the file systems you request into smaller file systems to fit the available disk space. So, after auto-layout completes, you may find file systems in the layout that you did not select from the list below. File Systems for Auto-layout ======================================== [X] / [ ] /opt [X] /usr [ ] /usr/openwin [X] /var [X] swap F2_Continue F5_Cancel F6_Help File System and Disk Layout The summary below is your current file system and disk layout, based on the information you've supplied. NOTE: If you choose to customize, you should understand file systems, their intended purpose on the disk, and how changing them may affect the operation of the system. File system/Mount point Disk/Slice Size ============================================================= / c0t3d0s0 73 MB /var c0t3d0s1 28 MB overlap c0t3d0s2 8652 MB swap c0t3d0s3 79 MB /usr c0t3d0s6 807 MB /export/home c0t3d0s7 7663 MB F2_Continue F3_Go Back F4_Customize F5_Exit F6_Help Mount Remote File Systems? Do you want to mount software from a remote file server? This may be necessary if you had to remove software because of disk space problems. F2_Continue F3_Go Back F4_Remote Mounts F5_Exit F6_Help Profile The information shown below is your profile for installing Solaris software. It reflects the choices you've made on previous screens. ============================================================================ Installation Option: Initial Boot Device: c0t3d0s0 Client Services: None Software: Solaris 2.7, Entire Distribution plus OEM s File System and Disk Layout: / c0t3d0s0 73 MB /var c0t3d0s1 28 MB swap c0t3d0s3 79 MB /usr c0t3d0s6 807 MB /export/home c0t3d0s7 7663 MB F2_Continue F4_Change F5_Exit F6_Help Reboot After Installation? After Solaris software is installed, the system must be rebooted. You can choose to have the system automatically reboot, or you can choose to manually reboot the system if you want to run scripts or do other customizations before the reboot. You can manually reboot a system by using the reboot(1M) command. [X] Auto Reboot [ ] Manual Reboot F2_Begin Installation F5_Cancel Preparing system for Solaris install Configuring disk (c0t3d0) - Creating Solaris disk label (VTOC) Creating and checking UFS file systems - Creating / (c0t3d0s0) - Creating /var (c0t3d0s1) - Creating /usr (c0t3d0s6) : : Solaris Initial Install MBytes Installed: 0.45 MBytes Remaining: 534.77 Installing: UTF-8 Locale Environment Common Files - | | | | | | 0 20 40 60 80 100 Solaris 2.7 software installation succeeded Customizing system files - Mount points table (/etc/vfstab) - Unselected disk mount points (/var/sadm/system/data/vfstab.unselected) - Network host addresses (/etc/hosts) Customizing system devices - Physical devices (/devices) - Logical devices (/dev) Installing boot information - Installing boot blocks (c0t3d0s0) Installation log location - /a/var/sadm/system/logs/install_log (before reboot) - /var/sadm/system/logs/install_log (after reboot) Installation complete Executing SolStart postinstall phase... Executing finish script "patch_finish"... Checking installed patches... One or more patch packages included in 107033-01 are not installed on this system. Patchadd is terminating. Checking installed patches... Verifying sufficient filesystem capacity (dry run method)... Installing patch packages... Patch number 106978-08 has been successfully installed. See /a/var/sadm/patch/106978-08/log for details Patch packages installed: SUNWadmap SUNWadmc Checking installed patches... Executing prepatch script... Verifying sufficient filesystem capacity (dry run method)... Installing patch packages... Patch number 106857-09 has been successfully installed. See /a/var/sadm/patch/106857-09/log for details Patch packages installed: SUNWpldte SUNWplow SUNWplow1 Finish script patch_finish execution completed. Executing JumpStart postinstall phase... The begin script log 'begin.log' is located in /var/sadm/system/logs after reboot. The finish script log 'finish.log' is located in /var/sadm/system/logs after reboot. syncing file systems... done rebooting... Resetting ... screen not found. Can't open input device. Keyboard not present. Using tty for input and output. SPARC CPU-8VT, No Keyboard ROM Rev. 2.15.1, 64 MB memory installed, Serial #9172389. Ethernet address 0:80:42:b:85:a5, Host ID: 808bf5a5. Rebooting with command: Boot device: /iommu/sbus/espdma@5,8400000/esp@5,8800000/sd@3,0 File and args: SunOS Release 5.7 Version Generic_106541-06 [UNIX(R) System V Release 4.0] Copyright (c) 1983-1999, Sun Microsystems, Inc. configuring network interfaces: le0. Hostname: onl8v1 Configuring the /devices directory Configuring the /dev directory Configuring the /dev directory (compatibility devices) The system is coming up. Please wait. checking ufs filesystems /dev/rdsk/c0t3d0s7: is clean. Configuring network interface addresses: le0 le1le1: No carrier - cable disconne cted or hub link test disabled? le1: No carrier - cable disconnected or hub link test disabled? . RPC: Timed out : : On this screen you can create a root password. A root password can contain any number of characters, but only the first eight characters in the password are significant. (For example, if you create `a1b2c3d4e5f6' as your root password, you can use `a1b2c3d4' to gain root access.) You will be prompted to type the root password twice; for security, the password will not be displayed on the screen as you type it. > If you do not want a root password, press RETURN twice. Root password: Re-enter your root password. Press Return to continue. System identification is completed. Setting netmask of le0 to 255.255.248.0 Setting default interface for multicast: add net 224.0.0.0: gateway onl8v1 syslog service starting. Print services started. volume management starting. The system is ready. onl8v1 console login: ok. システム・インストールは正常に終了した。 (4-2). システム情報をチェックする onl8v1 console login: root Password: Oct 5 15:55:09 onl8v1 login: ROOT LOGIN /dev/console Sun Microsystems Inc. SunOS 5.7 Generic October 1998 # ls -l total 97 lrwxrwxrwx 1 root root 9 Oct 5 15:03 bin -> ./usr/bin drwxr-xr-x 3 root nobody 512 Oct 5 15:51 cdrom drwxrwxr-x 18 root sys 3584 Oct 5 15:51 dev drwxrwxr-x 5 root sys 512 Oct 5 15:39 devices drwxr-xr-x 32 root sys 3072 Oct 5 15:51 etc drwxrwxr-x 3 root sys 512 Oct 5 15:00 export dr-xr-xr-x 1 root root 1 Oct 5 15:51 home drwxr-xr-x 9 root sys 512 Oct 5 15:03 kernel lrwxrwxrwx 1 root root 9 Oct 5 15:03 lib -> ./usr/lib drwx------ 2 root root 8192 Oct 5 14:59 lost+found drwxrwxr-x 2 root sys 512 Oct 5 15:03 mnt dr-xr-xr-x 1 root root 1 Oct 5 15:51 net drwxrwxr-x 6 root sys 512 Oct 5 15:33 opt drwxr-xr-x 4 root sys 1024 Oct 5 15:04 platform dr-xr-xr-x 30 root root 16064 Oct 5 15:55 proc drwxrwxr-x 2 root sys 512 Oct 5 15:08 sbin drwxrwxrwt 7 sys sys 318 Oct 5 15:51 tmp drwxrwxr-x 31 root sys 1024 Oct 5 15:32 usr drwxr-xr-x 25 root sys 512 Oct 5 15:51 var dr-xr-xr-x 6 root root 512 Oct 5 15:51 vol dr-xr-xr-x 1 root root 1 Oct 5 15:51 xfn # # df -k Filesystem kbytes used avail capacity Mounted on /proc 0 0 0 0% /proc /dev/dsk/c0t3d0s0 70047 27497 35546 44% / /dev/dsk/c0t3d0s6 776511 508327 213829 71% /usr fd 0 0 0 0% /dev/fd /dev/dsk/c0t3d0s1 27615 5351 19503 22% /var /dev/dsk/c0t3d0s7 7723221 9 7645980 1% /export/home swap 110608 12 110596 1% /tmp /vol/dev/dsk/c0t6d0/sol_7_899_sparc/s5 1006 4 902 1% /cdrom/sol_7_899_sparc/s5 /vol/dev/dsk/c0t6d0/sol_7_899_sparc/s4 1006 4 902 1% /cdrom/sol_7_899_sparc/s4 /vol/dev/dsk/c0t6d0/sol_7_899_sparc/s3 1006 4 902 1% /cdrom/sol_7_899_sparc/s3 /vol/dev/dsk/c0t6d0/sol_7_899_sparc/s2 1006 4 902 1% /cdrom/sol_7_899_sparc/s2 /vol/dev/dsk/c0t6d0/sol_7_899_sparc/s1 47974 39244 3934 91% /cdrom/sol_7_899_sparc/s1 /vol/dev/dsk/c0t6d0/sol_7_899_sparc/s0 539596 539596 0 100% /cdrom/sol_7_899_sparc/s0 # # prtconf -v System Configuration: Sun Microsystems sun4m Memory size: 64 Megabytes System Peripherals (Software Nodes): FORCE,CPU-8VT System properties: name length <4> value <0x00000002>. name length <4> value <0x00000001>. name length <4> value <0x00000fff>. name length <4> value <0x00001000>. name length <4> value <0x00001000>. packages (driver not attached) disk-label (driver not attached) deblocker (driver not attached) obp-tftp (driver not attached) busnet-demo (driver not attached) options, instance #0 System properties: name length <36> value <0x0000250200001805000000bd00008a3b031c7f150400000011131a1 9120f171600000000>. name length <5> value <0x726f6f7400>. aliases (driver not attached) openprom (driver not attached) iommu, instance #0 Driver properties: name length <18> value <0x6e6f2d73757370656e642d726573756d6500>. Register Specifications: Bus Type=0x0, Address=0x10000000, Size=0x300 sbus, instance #0 Register Specifications: Bus Type=0x0, Address=0x10001000, Size=0x28 Range Specifications: Ch: 00,00000000 Pa: 00,20000000, Sz: 10000000 Ch: 01,00000000 Pa: 00,30000000, Sz: 10000000 Ch: 02,00000000 Pa: 00,40000000, Sz: 10000000 Ch: 03,00000000 Pa: 00,50000000, Sz: 10000000 Ch: 04,00000000 Pa: 00,60000000, Sz: 10000000 Ch: 05,00000000 Pa: 00,70000000, Sz: 10000000 VME (driver not attached) busnet (driver not attached) espdma, instance #0 Register Specifications: Bus Type=0x5, Address=0x8400000, Size=0x10 esp, instance #0 Driver properties: name length <4> value <0x00001653>. name length <4> value <0x00002710>. name length <4> value <0x00002710>. name length <0> -- . name length <0> -- . name length <4> value <0x00001ff8>. name length <4> value <0x0000000a>. name length <4> value <0x00000002>. name length <4> value <0x00000bb8>. Register Specifications: Bus Type=0x5, Address=0x8800000, Size=0x40 Interrupt Specifications: Interrupt Priority=0x24 (ipl 4) sd (driver not attached) st (driver not attached) sd, instance #0 (driver not attached) System properties: name length <4> value <0x00000000>. name length <4> value <0x00000000>. name length <6> value <0x617461706900>. name length <5> value <0x7363736900>. sd, instance #1 (driver not attached) System properties: name length <4> value <0x00000000>. name length <4> value <0x00000001>. name length <6> value <0x617461706900>. name length <5> value <0x7363736900>. sd, instance #2 System properties: name length <4> value <0x00000000>. name length <4> value <0x00000002>. name length <6> value <0x617461706900>. name length <5> value <0x7363736900>. Driver properties: name length <21> value <0x6e656564732d73757370656e642d726573756d6 500>. name length <0> -- . sd, instance #3 System properties: name length <4> value <0x00000000>. name length <4> value <0x00000003>. name length <6> value <0x617461706900>. name length <5> value <0x7363736900>. Driver properties: name length <21> value <0x6e656564732d73757370656e642d726573756d6 500>. name length <0> -- . sd, instance #4 (driver not attached) System properties: name length <4> value <0x00000000>. name length <4> value <0x00000004>. name length <5> value <0x7363736900>. sd, instance #5 (driver not attached) System properties: name length <4> value <0x00000000>. name length <4> value <0x00000005>. name length <5> value <0x7363736900>. sd, instance #6 System properties: name length <4> value <0x00000000>. name length <4> value <0x00000006>. name length <5> value <0x7363736900>. Driver properties: name length <21> value <0x6e656564732d73757370656e642d726573756d6 500>. name length <0> -- . SUNW,bpp, instance #0 (driver not attached) Hardware properties: name length <10> value <0x352c6338303030303000>. ledma, instance #0 Driver properties: name length <4> value <0xf5974d80>. Register Specifications: Bus Type=0x5, Address=0x8400010, Size=0x20 le, instance #0 Register Specifications: Bus Type=0x5, Address=0x8c00000, Size=0x4 Interrupt Specifications: Interrupt Priority=0x26 (ipl 6) espdma, instance #1 Register Specifications: Bus Type=0x5, Address=0x8400040, Size=0x10 esp, instance #1 Driver properties: name length <4> value <0x00001ff8>. name length <4> value <0x0000000a>. name length <4> value <0x00000002>. name length <4> value <0x00000bb8>. Register Specifications: Bus Type=0x5, Address=0x8800040, Size=0x40 Interrupt Specifications: Interrupt Priority=0x24 (ipl 4) sd (driver not attached) st (driver not attached) sd, instance #7 (driver not attached) System properties: name length <4> value <0x00000000>. name length <4> value <0x00000000>. name length <6> value <0x617461706900>. name length <5> value <0x7363736900>. sd, instance #8 (driver not attached) System properties: name length <4> value <0x00000000>. name length <4> value <0x00000001>. name length <6> value <0x617461706900>. name length <5> value <0x7363736900>. sd, instance #9 (driver not attached) System properties: name length <4> value <0x00000000>. name length <4> value <0x00000002>. name length <6> value <0x617461706900>. name length <5> value <0x7363736900>. sd, instance #10 (driver not attached) System properties: name length <4> value <0x00000000>. name length <4> value <0x00000003>. name length <6> value <0x617461706900>. name length <5> value <0x7363736900>. sd, instance #11 (driver not attached) System properties: name length <4> value <0x00000000>. name length <4> value <0x00000004>. name length <5> value <0x7363736900>. sd, instance #12 (driver not attached) System properties: name length <4> value <0x00000000>. name length <4> value <0x00000005>. name length <5> value <0x7363736900>. sd, instance #13 (driver not attached) System properties: name length <4> value <0x00000000>. name length <4> value <0x00000006>. name length <5> value <0x7363736900>. ledma, instance #1 Driver properties: name length <4> value <0xf5974d60>. Register Specifications: Bus Type=0x5, Address=0x8400050, Size=0x20 le, instance #1 Register Specifications: Bus Type=0x5, Address=0x8c00040, Size=0x4 Interrupt Specifications: Interrupt Priority=0x26 (ipl 6) obio, instance #0 Range Specifications: Ch: 00,00000000 Pa: 00,71000000, Sz: 1000000 zs, instance #0 Register Specifications: Bus Type=0x0, Address=0x100000, Size=0x8 Interrupt Specifications: Interrupt Priority=0x2c (ipl 12) zs, instance #1 Register Specifications: Bus Type=0x0, Address=0x0, Size=0x8 Interrupt Specifications: Interrupt Priority=0x2c (ipl 12) eeprom (driver not attached) slavioconfig (driver not attached) auxio (driver not attached) counter (driver not attached) interrupt (driver not attached) power (driver not attached) SUNW,fdtwo, instance #0 (driver not attached) Hardware properties: name length <9> value <0x302c34303030303000>. flash-memory (driver not attached) memory (driver not attached) virtual-memory (driver not attached) sysconfig (driver not attached) FMI,MB86907 (driver not attached) pseudo, instance #0 System properties: name length <5> value <0x726f6f7400>. # # prtvtoc /dev/rdsk/c0t3d0s2 * /dev/rdsk/c0t3d0s2 partition map * * Dimensions: * 512 bytes/sector * 246 sectors/track * 8 tracks/cylinder * 1968 sectors/cylinder * 9006 cylinders * 9004 accessible cylinders * * Flags: * 1: unmountable * 10: read-only * * First Sector Last * Partition Tag Flags Sector Count Sector Mount Directory 0 2 00 0 149568 149567 / 1 7 00 149568 59040 208607 /var 2 5 00 0 17719872 17719871 3 3 01 208608 163344 371951 6 4 00 371952 1653120 2025071 /usr 7 8 00 2025072 15694800 17719871 /export/home # ok. システム・インストールは正常終了した。 以降、/etc の下の設定、およびユーザ登録をやる。 ---xxxx ( ここまでやった 継続中) --- (6). セクション (6-1). サブセクション (6-1-1). サブサブセクション