Sep 15, 2001 onl54: Solaris 8 cc ドライバのテスト. Solaris 8 システムのインストール --- システム・インストール#01 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ (http://www-online.kek.jp/~inoue/Machine/onl54/ Solaris8/system-install1.txt) 高エネルギー加速器研究機構 素粒子原子核研究所 物理、オンライングループ 井上 栄二 (1). 現状確認 (A). Solaris8 6/00 が届いた。 (B). FORCE SPARC CPU-54 が届いた (2). ここでやるべきこと FORCE,CPU-54(UltraSPARC-IIe 400MHz)、に Solaris 8 のシステムを インストールする。 (3). CPU-54 ボードの設置 VMEクレート、スロット1に CPUボードを設置する。 (4-1). CPUボードの配置 onl54 は VMEクレートのスロット番号1に挿入した。 onl54 の SCSI には ローカル・ディスクを ID #3 で接続し、には CD-ROMドライブを ID #6 で 接続した。 他に CPUボードは挿してない。 (4-2). onl54 の挿入してある VMEクレートの電源を入れる メディア "SOLARIS 8 INSTALLATION 6/00" を CD-ROM にセットした。 ok screen not found. keyboard not found. Keyboard not present. Using ttya for input and output. FORCE,CPU-54 (UltraSPARC-IIe 404MHz), No Keyboard OpenBoot 4.0, 128 MB memory installed, Serial #9229550. Ethernet address 0:80:42:10:70:28, Host ID: 808cd4ee. Drive not ready Can't read disk label. Can't open disk label package Boot device: net File and args: Timeout waiting for ARP/RARP packet Timeout waiting for ARP/RARP packet Timeout waiting for ARP/RARP packet ~ Type 'go' to resume ok <-- 割り込みキーを押して止めた。 ブートコマンドを入力する。 ok ok boot cdrom Resetting ... screen not found. keyboard not found. Keyboard not present. Using ttya for input and output. FORCE,CPU-54 (UltraSPARC-IIe 404MHz), No Keyboard OpenBoot 4.0, 128 MB memory installed, Serial #9229550. Ethernet address 0:80:42:10:70:28, Host ID: 808cd4ee. Rebooting with command: boot cdrom Boot device: /pci@1f,0/pci@3/scsi@4/disk@6,0:f File and args: krtld: load_exec: fail to expand cpu/$CPU krtld: error during initial load/link phase panic - boot: exitto64 returned from client program Program terminated ok CD-ROMにアクセスしてしばらく読み始めたが failのメッセージが表示されて インストールは中断された。 (4-3). (株)エル・エッチ・エスよりHDおよびCPUボードを借用してチェック (株)エル・エッチ・エスで正常に動作しているHD、SCSIケーブルおよびCPU ボードを借用してシステムインストールできない原因を調べる。 (4-3-1). CPU-54を交換してシステムインストールを試みる これまで、SolflowerのVMEクレートで試みていたが、ここでは Schroffの クレートを使ってやってみる。 Schroffのクレートのスロット#1に新たに 借りたCPU-54を挿した。 この状態で boot cd-rom をやってみたが状況は変わ らない。 (4-3-2). Solaris 8 4/01バージョンでシステムインストールを試みる ok ok screen not found. keyboard not found. Keyboard not present. Using ttya for input and output. FORCE,CPU-54 (UltraSPARC-IIe 404MHz), No Keyboard OpenBoot 4.0, 128 MB memory installed, Serial #9229550. Ethernet address 0:80:42:10:70:28, Host ID: 808cd4ee. Drive not ready Can't read disk label. Can't open disk label package Boot device: net File and args: ~ Type 'go' to resume ok ok ok ok ok ok boot cdrom Resetting ... screen not found. keyboard not found. Keyboard not present. Using ttya for input and output. FORCE,CPU-54 (UltraSPARC-IIe 404MHz), No Keyboard OpenBoot 4.0, 128 MB memory installed, Serial #9229550. Ethernet address 0:80:42:10:70:28, Host ID: 808cd4ee. Rebooting with command: boot cdrom Boot device: /pci@1f,0/pci@3/scsi@4/disk@6,0:f File and args: SunOS Release 5.8 Version Generic_108528-07 64-bit Copyright 1983-2001 Sun Microsystems, Inc. All rights reserved. Configuring /dev and /devices WARNING: i2c_client_register failed Using RPC Bootparams for network configuration information. SUNW,hme0 : No response from Ethernet network : Link down -- cable problem? Skipping interface hme0 Select a Language 0. English 1. French 2. German 3. Italian 4. Japanese 5. Korean 6. Simplified Chinese 7. Spanish 8. Swedish 9. Traditional Chinese Please make a choice (0 - 9), or press h or ? for help: 4 Select a Locale 0. Japanese EUC (ja) 1. Japanese PC Kanji (ja_JP.PCK) 2. Japanese UTF-8 (ja_JP.UTF-8) 3. Go Back to Previous Screen Please make a choice (0 - 3), or press h or ? for help: 0 どのタイプの端末を使用していますか? 1) ANSI 標準 CRT 2) DEC VT52 3) DEC VT100 4) Heathkit 19 5) Lear Siegler ADM31 6) PC コンソール 7) Sun コマンドツール 8) Sun ワークステーション 9) Televideo 910 10) Televideo 925 11) Wyse Model 50 12) X 端末エミュレータ (xterms) 13) その他 選択する番号を入力して、Return キーを押してください。12 The system is coming up. Please wait. q The Solaris Installation Program qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq The Solaris installation program is divided into a series of short sections where you'll be prompted to provide information for the installation. At the end of each section, you'll be able to change the selections you've made before continuing. About navigation... - The mouse cannot be used - If your keyboard does not have function keys, or they do not respond, press ESC; the legend at the bottom of the screen will change to show the ESC keys to use for navigation. qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Identify This System qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On the next screens, you must identify this system as networked or non-networked, and set the default time zone and date/time. If this system is networked, the software will try to find the information it needs to identify your system; you will be prompted to supply any information it cannot find. > To begin identifying this system, press F2. qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Network Connectivity qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq Specify Yes if the system is connected to the network by one of the Solaris or vendor network/communication Ethernet cards that are supported on the Solaris CD. See your hardware documentation for the current list of supported cards. Specify No if the system is connected to a network/communication card that is not supported on the Solaris CD, and follow the instructions listed under Help. Networked qqqqqqqqq [X] Yes [ ] No qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q DHCP qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must specify whether or not this system should use DHCP for network interface configuration. Choose Yes if DHCP is to be used, or No if the interfaces are to be configured manually. WARNING: Because this machine booted from the network, DHCP support will not be enabled, if selected, until after the system reboots. Use DHCP qqqqqqqq [ ] Yes [X] No qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Host Name qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must enter your host name, which identifies this system on the network. The name must be unique within your domain; creating a duplicate host name will cause problems on the network after you install Solaris. A host name must be at least two characters; it can contain letters, digits, and minus signs (-). Host name: onl54 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q IP Address qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must enter the Internet Protocol (IP) address for this system. It must be unique and follow your site's address conventions, or a system/network failure could result. IP addresses contain four sets of numbers separated by periods (for example 129.200.9.1). IP address: 130.87.220.59 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Subnets qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must specify whether this system is part of a subnet. If you specify incorrectly, the system will have problems communicating on the network after you reboot. > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X]. System part of a subnet qqqqqqqqqqqqqqqqqqqqqqq [X] Yes [ ] No qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Netmask qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must specify the netmask of your subnet. A default netmask is shown; do not accept the default unless you are sure it is correct for your subnet. A netmask must contain four sets of numbers separated by periods (for example 255.255.255.0). Netmask: 255.255.248.0 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q IPv6 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you should specify whether or not IPv6, the next generation Internet Protocol, will be enabled on this machine. Enabling IPv6 will have no effect if this machine is not on a network that provides IPv6 service. IPv4 service will not be affected if IPv6 is enabled. > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X]. Enable IPv6 qqqqqqqqqqq [X] Yes [ ] No qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Confirm Information qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq > Confirm the following information. If it is correct, press F2; to change any information, press F4. Networked: Yes Use DHCP: No Host name: onl54 IP address: 130.87.220.59 System part of a subnet: Yes Netmask: 255.255.248.0 Enable IPv6: Yes qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F4_Change F6_Help q Configure Security Policy: qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq Specify Yes if the system will use the Kerberos security mechanism. Specify No if this system will use standard UNIX security. Configure Kerberos Security qqqqqqqqqqqqqqqqqqqqqqqqqqq [ ] Yes [X] No qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Confirm Information qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq > Confirm the following information. If it is correct, press F2; to change any information, press F4. Configure Kerberos Security: No qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F4_Change F6_Help q Name Service qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must provide name service information. Select the name service that will be used by this system, or None if your system will either not use a name service at all, or if it will use a name service not listed here. > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X]. Name service qqqqqqqqqqqq [ ] NIS+ [ ] NIS [X] DNS [ ] LDAP [ ] None qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Domain Name qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must specify the domain where this system resides. Make sure you enter the name correctly including capitalization and punctuation. Domain name: kek.jp qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q DNS Server Addresses qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must enter the IP address of your DNS server(s). You must enter at least one address. IP addresses must contain four sets of numbers separated by periods (for example 129.200.9.1). Server's IP address: 130.87.216.2 Server's IP address: 130.87.34.2 Server's IP address: 130.87.34.6 > Press F2 to go to the next screen. qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q DNS Search List qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you can enter a list of domains that will be searched when a DNS query is made. If you do not enter any domains, DNS will only search the DNS domain chosen for this system. The domains entered, when concatenated, may not be longer than 250 characters. Search domain: Search domain: Search domain: Search domain: Search domain: Search domain: qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Confirm Information qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq > Confirm the following information. If it is correct, press F2; to change any information, press F4. Name service: DNS Domain name: kek.jp Server address(es): 130.87.216.2 130.87.34.2 130.87.34.6 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F4_Change F6_Help Just a moment... qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq SUNW,hme0 : No response from Ethernet network : Link down -- cable problem? SUNW,hme0 : No response from Ethernet network : Link down -- cable problem? SUNW,hme0 : No response from Ethernet network : Link down -- cable problem? q Name Service Error qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq Unable to find an address entry for onl54 with the specified DNS configuration. Enter new name service information? qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq [X] Yes [ ] No qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Name Service qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must provide name service information. Select the name service that will be used by this system, or None if your system will either not use a name service at all, or if it will use a name service not listed here. > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X]. Name service qqqqqqqqqqqq [ ] NIS+ [ ] NIS [X] DNS [ ] LDAP [ ] None qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Domain Name qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must specify the domain where this system resides. Make sure you enter the name correctly including capitalization and punctuation. Domain name: kek.jp > Press F2 to go to the next screen. qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q DNS Server Addresses qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must enter the IP address of your DNS server(s). You must enter at least one address. IP addresses must contain four sets of numbers separated by periods (for example 129.200.9.1). Server's IP address: 130.87.34.2 Server's IP address: 130.87.216.2 Server's IP address: 130.87.34.6 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q DNS Search List qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you can enter a list of domains that will be searched when a DNS query is made. If you do not enter any domains, DNS will only search the DNS domain chosen for this system. The domains entered, when concatenated, may not be longer than 250 characters. Search domain: Search domain: Search domain: Search domain: Search domain: Search domain: qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Confirm Information qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq > Confirm the following information. If it is correct, press F2; to change any information, press F4. Name service: DNS Domain name: kek.jp Server address(es): 130.87.34.2 130.87.216.2 130.87.34.6 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F4_Change F6_Help q Name Service Error qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq Unable to find an address entry for onl54 with the specified DNS configuration. Enter new name service information? qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq [X] Yes [ ] No qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Name Service qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must provide name service information. Select the name service that will be used by this system, or None if your system will either not use a name service at all, or if it will use a name service not listed here. > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X]. Name service qqqqqqqqqqqq [ ] NIS+ [ ] NIS [X] DNS [ ] LDAP [ ] None qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Domain Name qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must specify the domain where this system resides. Make sure you enter the name correctly including capitalization and punctuation. Domain name: kek.jp qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q DNS Server Addresses qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must enter the IP address of your DNS server(s). You must enter at least one address. IP addresses must contain four sets of numbers separated by periods (for example 129.200.9.1). Server's IP address: 130.87.216.2 Server's IP address: 130.87.34.2 Server's IP address: 130.87.34.6 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q DNS Search List qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you can enter a list of domains that will be searched when a DNS query is made. If you do not enter any domains, DNS will only search the DNS domain chosen for this system. The domains entered, when concatenated, may not be longer than 250 characters. Search domain: Search domain: Search domain: Search domain: Search domain: Search domain: qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Confirm Information qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq > Confirm the following information. If it is correct, press F2; to change any information, press F4. Name service: DNS Domain name: kek.jp Server address(es): 130.87.216.2 130.87.34.2 130.87.34.6 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F4_Change F6_Help CPU-54 EtherNet3 に接続してあった、これを EtherNet1につなぎ変えたら 正常にネットワークにアクセスできた。 q Time Zone qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must specify your default time zone. You can specify a time zone in three ways: select one of the geographic regions from the list, select other - offset from GMT, or other - specify time zone file. > To make a selection, use the arrow keys to highlight the option and press Return to mark it [X]. Regions qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq ^ [ ] Asia, Western x [ ] Australia / New Zealand x [ ] Canada x [ ] Europe x [ ] Mexico x [ ] South America x [ ] United States x [ ] other - offset from GMT - [X] other - specify time zone file qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Time Zone File qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq Specify the time zone file you want to use. The file must already be in the /usr/share/lib/zoneinfo directory. You do not need to enter the full path. File name: Japan qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F5_Cancel F6_Help q Date and Time qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq > Accept the default date and time or enter new values. Date and time: 2001-09-18 16:02 Year (4 digits) : 2001 Month (1-12) : 09 Day (1-31) : 18 Hour (0-23) : 16 Minute (0-59) : 02 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F6_Help q Confirm Information qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq > Confirm the following information. If it is correct, press F2; to change any information, press F4. Time zone: Japan Date and time: 2001-09-18 16:02:00 qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F4_Change F6_Help System identification is completed. Starting Solaris installation program... Executing JumpStart preinstall phase... Searching for SolStart directory... Checking rules.ok file... Using begin script: install_begin Using finish script: patch_finish Executing SolStart preinstall phase... Executing begin script "install_begin"... Begin script install_begin execution completed. q Solaris Interactive Installation qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq You'll be using the initial option for installing Solaris software on the system. The initial option overwrites the system disks when the new Solaris software is installed. On the following screens, you can accept the defaults or you can customize how Solaris software will be installed by: - Selecting the type of Solaris software to install - Selecting disks to hold software you've selected - Specifying how file systems are laid out on the disks After completing these tasks, a summary of your selections (called a profile) will be displayed. There are two ways to install your Solaris software: - "Standard" installs your system from a standard Solaris Distribution. - "Flash" installs your system from one or more Flash Archives. qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Standard F4_Flash F5_Exit F6_Help q Select Geographic Regions qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq Select the geographic regions for which support should be installed. > [X] Asia > [ ] Eastern Europe > [ ] Middle East > [ ] Central America > [ ] South America > [ ] Northern Europe > [ ] Southern Europe > [ ] Central Europe > [ ] North America > [ ] Australasia > [ ] Western Europe > [ ] Northern Africa Region is selected. Press Return to deselect qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F3_Go Back F5_Exit F6_Help q Select 64 Bit qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq Select 64-bit if you want to install the Solaris 64-bit packages on this system. [X] Select To Include Solaris 64-bit Support qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F3_Go Back F5_Exit q Select Software qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq Select the Solaris software to install on the system. NOTE: After selecting a software group, you can add or remove software by customizing it. However, this requires understanding of software dependencies and how Solaris software is packaged. The software groups displaying 64-bit contain 64-bit support. [X] Entire Distribution plus OEM support 64-bit 2179.00 MB (F4 to Custom ize [ ] Entire Distribution 64-bit ................. 2146.00 MB [ ] Developer System Support 64-bit ............ 2094.00 MB [ ] End User System Support 64-bit ............. 1615.00 MB [ ] Core System Support 64-bit ................. 334.00 MB qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F3_Go Back F4_Customize F5_Exit F6_Help q Select Disks qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must select the disks for installing Solaris software. Start by looking at the Suggested Minimum field; this value is the approximate space needed to install the software you've selected. Keep selecting disks until the Total Selected value exceeds the Suggested Minimum value. Disk Device (Size) Available Space ============================================= [X] c0t3d0 (38929 MB) 38929 MB Total Selected: 0 MB Suggested Minimum: 1743 MB qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F3_Go Back F4_Edit F5_Exit F6_Help q Preserve Data? qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq Do you want to preserve existing data? At least one of the disks you've selected for installing Solaris software has file systems or unnamed slices that you may want to save. qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F3_Go Back F4_Preserve F5_Exit F6_Help q Automatically Layout File Systems? qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq Do you want to use auto-layout to automatically layout file systems? Manually laying out file systems requires advanced system administration skills. qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Auto Layout F3_Go Back F4_Manual Layout F5_Exit F6_Help q Automatically Layout File Systems qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq On this screen you must select all the file systems you want auto-layout to create, or accept the default file systems shown. NOTE: For small disks, it may be necessary for auto-layout to break up some of the file systems you request into smaller file systems to fit the available disk space. So, after auto-layout completes, you may find file systems in the layout that you did not select from the list below. File Systems for Auto-layout ======================================== [X] / [ ] /opt [X] /usr [ ] /usr/openwin [X] /var [X] swap qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F5_Cancel F6_Help q File System and Disk Layout qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq The summary below is your current file system and disk layout, based on the information you've supplied. NOTE: If you choose to customize, you should understand file systems, their intended purpose on the disk, and how changing them may affect the operation of the system. File system/Mount point Disk/Slice Size ============================================================= / c0t3d0s0 140 MB /var c0t3d0s1 50 MB overlap c0t3d0s2 38929 MB swap c0t3d0s3 148 MB /usr c0t3d0s6 2193 MB /export/home c0t3d0s7 36396 MB qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F3_Go Back F4_Customize F5_Exit F6_Help q Mount Remote File Systems? qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq Do you want to mount software from a remote file server? This may be necessary if you had to remove software because of disk space problems. qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F3_Go Back F4_Remote Mounts F5_Exit F6_Help q Profile qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq The information shown below is your profile for installing Solaris software. It reflects the choices you've made on previous screens. ============================================================================ Installation Option: Initial Boot Device: c0t3d0 Client Services: None Regions: Asia Software: Solaris 8, Entire Distribution plus OEM sup File System and Disk Layout: / c0t3d0s0 140 MB /var c0t3d0s1 50 MB swap c0t3d0s3 148 MB /usr c0t3d0s6 2193 MB /export/home c0t3d0s7 36396 MB qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Continue F4_Change F5_Exit F6_Help q Warning qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq The following disk configuration condition(s) have been detected. Errors must be fixed to ensure a successful installation. Warnings can be ignored without causing the installation to fail. WARNING: CHANGING DEFAULT BOOT DEVICE You have either explicitly changed the default boot device, or accepted the default to "Reconfigure EEPROM". In either case, the system's EEPROM will be changed so it will always boot Solaris from the device that you've specified. If this is not what you had in mind, go back to the disk selection screens and change the "Reconfigure EEPROM" setting. qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_OK F5_Cancel q Reboot After Installation? qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq After Solaris software is installed, the system must be rebooted. You can choose to have the system automatically reboot, or you can choose to manually reboot the system if you want to run scripts or do other customizations before the reboot. You can manually reboot a system by using the reboot(1M) command. [X] Auto Reboot [ ] Manual Reboot qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq F2_Begin Installation F5_Cancel Preparing system for Solaris install Configuring disk (c0t3d0) - Creating Solaris disk label (VTOC) Creating and checking UFS file systems - Creating / (c0t3d0s0) - Creating /var (c0t3d0s1) - Creating /usr (c0t3d0s6) - Creating /export/home (c0t3d0s7) Solaris Initial Install MBytes Installed: 0.03 MBytes Remaining: 1460.30 Installing: X Window System Runtime Compatibility Package (64-bit) | | | | | | | 0 20 40 60 80 100 System identification is completed. Setting netmask of hme0 to 255.255.248.0 Setting default IPv4 interface for multicast: add net 224.0/4: gateway onl54 syslog service starting. Print services started. volume management starting. Starting Web Start Launcher in Command Line Mode. Please specify the media from which you will install Solaris 8 (SPARC) Software 2. Alternatively, choose the selection for "Skip" to skip this CD and go on to the next one. Media: 1. CD 2. Network File System 3. Skip Media [1]: Please insert the CD for Solaris 8 (SPARC) Software 2. After you insert the CD, please press Enter. Enter S to skip this CD and go on to the next one. To select a different media, enter B to go Back. [] Launching installer for Solaris 8 (SPARC) Software 2. Please Wait... Installing Solaris 8 Software 2 |-1%--------------25%-----------------50%-----------------75%--------------100%| Installation details: Product Result More Info 1. Solaris 8 Software 2 Installed Available 2. Done Enter the number corresponding to the desired selection for more information, or enter 2 to continue [2]: End of Solaris 8 Software 2 installation. Please specify the media from which you will install Solaris 8 Languages (SPARC Platform Edition). Alternatively, choose the selection for "Skip" to skip this CD and go on to the next one. Media: 1. CD 2. Network File System 3. Skip Media [1]: Please insert the CD for Solaris 8 Languages (SPARC Platform Edition). After you insert the CD, please press Enter. Enter S to skip this CD and go on to the next one. To select a different media, enter B to go Back. [] 3 Please type one of '' 'S' or 'B' [] S Sep 18 17:20:16 onl54 reboot: rebooted by root Sep 18 17:20:16 onl54 syslogd: going down on signal 15 Sep 18 17:20:16 rpcbind: rpcbind terminating on signal. Sep 18 17:20:16 cssd: Got sig#15, sending it to all CSes and exit Sep 18 17:20:16 in.ndpd[206]: terminated syncing file systems... done rebooting... Resetting ... screen not found. keyboard not found. Keyboard not present. Using ttya for input and output. FORCE,CPU-54 (UltraSPARC-IIe 404MHz), No Keyboard OpenBoot 4.0, 128 MB memory installed, Serial #9229550. Ethernet address 0:80:42:10:70:28, Host ID: 808cd4ee. Rebooting with command: boot Boot device: disk3:a File and args: SunOS Release 5.8 Version Generic_108528-07 64-bit Copyright 1983-2001 Sun Microsystems, Inc. All rights reserved. configuring IPv4 interfaces: hme0. configuring IPv6 interfaces: hme0. Hostname: onl54 Configuring /dev and /devices WARNING: i2c_client_register failed Configuring the /dev directory (compatibility devices) The system is coming up. Please wait. checking ufs filesystems /dev/rdsk/c0t3d0s7: is clean. Starting IPv4 routing daemon. Starting IPv6 neighbor discovery. Setting default IPv6 interface for multicast: add net ff00::/8: gateway fe80::280:42ff:fe10:7028 starting rpc services: rpcbind done. Setting netmask of hme0 to 255.255.248.0 Setting default IPv4 interface for multicast: add net 224.0/4: gateway onl54 syslog service starting. Print services started. volume management starting. The system is ready. onl54 console login: ok. システムインストールは最後まで実行できた。 FORCE CPU-54 は、Solaris 8 6/00のバージョンでは正常にインストールできな い、Solaris 8 4/01バージョンであれば正常にインストールできる。 ---xxxx(ここまでやった、継続中) --- (6). セクション (6-1). サブセクション (6-1-1). サブサブセクション